Features:

• IEEE: 1000BASE-SX
• Speed: 1000 Mbps Ethernet
• Media type: Multimode fiber
• Wavelength: 850nm
• Form factor: SFP
• Optical connector: Duplex LC

The Model DXR-701 is a digital receiver with an isolated relay output designed for use with Linears DX Format transmitters. This receiver can be used in a variety of remote control applications. When the receiver detects a signal from a transmitter programmed into its memory, the relay output activates. The relay has four optional output configurations.

In a typical installation, the receiver is connected to an alarm control panel, door strike, camera, high current relay or some other device. A transmitter is used to activate or control the device. The receiver should be mounted with the supplied mounting bracket indoors or outdoors inside a weather resistant non-metallic housing.

The digital DX code format features over a million possible codes. The DX transmitters are precoded at the factory to unique codes, so no field coding is required. Receivers must be programmed to the transmitters code before system testing and operation. Up to 32 transmitters can be programmed into the receivers memory. The memory is retained, even without power.

The unit can be powered from a 11-17 VDC or 12-16 VAC power source. The relays normally open and normally closed contacts can switch up to 1 amp at 24 volts AC/DC.

Cutting jumpers select how the relay activates. The factory setting causes the relay to engage for four seconds each activation. Optionally, the relay can be set to engage for one second, toggle on with one activation then off with the next, or latch engaged until reset by pressing the program button.

A nine-inch wire lead serves as the receivers antenna. The red program indicator lights during RF reception. The installer can verify that signals are being sent from transmitters and diagnose interference problems by viewing the indicator. The indicator also lights during memory programming/erasing and flashes to count the number of transmitters in memory.

Features:

• 32 transmitter capacity
• RF activity indicator
• Quick-learn programming
• Operates on 11-17 VDC or 12-16 VAC power
• One channel
• DX format
• One form C relay output
• One Amp contact rating @ 24 Volts AC/DC
• Selectable relay activation time
• Current consumption: 25 mA standby, 60 mA operating @ 12 VDC
• RF frequency: 315 MHz
• 5.5 in. W x 4.0 in. H x 1.25 in. D
• Order number: SNR00148

The Inovonics single input universal transmitter with EOL protection is a universal transmitter with an end of line resistor. The included 2.2k ohm resistor is required to operate the EN1210EOL.

Features:

• Mounting bracket included for quick and easy installation
• Can be used with almost any standard NO/NC contact
• Fully supervised
• Includes case tamper protection

The GEMC-BSLC-4PT is four point expansion module. Terminals are provided for four supervised zones supporting normally-closed or normally-open contacts. Each expansion module has a unique factory-programmed code (printed on the circuit board and on a label located on the rear case) that distinguishes itself to the receiver

The RC-20U is the reciever / chime for the RCTD-20U (Wireless 2000). The device is powered by a AC adaptor (included), and up to nine TD-20U's can be added to one RC-20U receiver. (With an additional three added to a latching zone) In addition, the RC-20U includes a Form-C relay for activating additional devices such as lights, a camera, door lock, ect.

***Products are backwards compatible and will work with the TC-10U & TD-10U Series***

Features:

• Accepts 9 transmitters, identifies each group of three with a different chime tone
• Operates with 9VDC adaptor (included)
• Wall mount or table mount design
• Form C relay for activating other devices (50V AC 1A max. or 24V DC 1A max.) with adjustable output duration

Adds 16 outputs (8 voltage, 8 relays) to M1 Gold or M1EZ8 Controls. Voltages can be used to trigger low current devices (50 mA max. each). Relays are SPDT rated for 7A @ 30 VDC, 10A @ 125 VAC. Operates from 4-wire data bus. Up to 12 output expanders may be used for a total of 208 outputs. Option: Convert 8 voltage outputs to relays using M1RB Relay Board.
Includes:

• Output Expander - 8 Relays/8 Voltage Outputs
• ELK-SWG Circuit Board Mounting Glides 2/pack
• Relay Adapter, 12 Conductor Cable Assembly
• Instructions

Features:

• PC4108A adds 8 hardwire zones
• AUX power rated at 250 mA (PTC protected)