|◀ ◀ 1 - 12 of 1213 ▶ ▶|
View:

30V - 66 Block Snap On Protec tion w/Diagnostic LED, for ana

Item#:
DTK-SL30B
You must be logged in to order this item. Log in here

35ft Select VGA Video Cable M/M - In-Wall CMG-Rated

The C2G Select VGA Video Cable is perfect for source to display connectivity for in-home desktop or in-wall commercial applications which require video resolutions of up to QXGA (2048x1536). The CMG rated jacket provides a solution for in-wall applications, while the low-profile, rounded connectors make installing in tight spaces, such as a projector mount pole, easy. This cable is designed to support high resolution video applications over long distances of up to 150ft. All 15 pins are wired providing support for DDC2 (E-DDC) and Extended Display Identification Data (EDID) signals, i.e. communication of the display's capabilities, ensuring that the content from the source is sent at the optimal resolution for the display.
  • In-wall, CMG-rated jacket
  • Supports up to a 2048x1536 resolution
  • All 15 pins wired to support DDC2 (E-DDC) and EDID
  • Low profile connectors
Item#:
CTG50217
 
Spec Sheet
You must be logged in to order this item. Log in here

Single Channel 10GbE PoE Prote ctor Shielded RJ45 Connection

DITEKs DTK-MRJPOES is designed with state-of-theart circuitry to provide superior protection for Shielded 10GbE Power over Ethernet connections. This point of use surge protector can be installed at the equipment end, or ahead of injectors and midspan devices.

  • Uses SAD and GDT technologies for superior protection
  • Data speeds up to 10GbE without signal degradation
  • PoE Plus, HiPoE ready for high-wattage applications
  • When used with STP cable, device does not require a separate earth ground

Item#:
DTK-MRJPOES
 
Manufacturer Brochure
Assembly Instructions
You must be logged in to order this item. Log in here

VGA BALUN II TX/RX SET

Item#:
MUX500040-42PK
You must be logged in to order this item. Log in here

WP2 Pole Mount Kit, For Outdoor Enclosures

Includes:

  • Two (2) powder coated steel mount brackets.
  • Four (4) stainless steel bolts.
  • Four (4) stainless steel lock washers.
  • Two (2) wormgear quick release straps.

Item#:
PMK2
You must be logged in to order this item. Log in here

35" Single-Sided Vertical Finger Ducts with T-Bracket in 4 Pack

  • Mounts on the side and in-between racks.
  • Feed-through holes help route cable from the rear.
  • Mounting bracket is pre-installed to finger duct for easy installation of vertical finger duct.
  • Compatible with most TIA specification distribution racks.
  • Modular design to suit todays cable management requirements.
  • Can be easily shipped using common carriers.
  • Four (4) Finger Duct per carton.

Item#:
ICCMSC30BK
You must be logged in to order this item. Log in here

PROGRAMMING

THIS IS NOT A PRODUCT FOR RESALE
Item#:
PALS PROGRAMMING
You must be logged in to order this item. Log in here

Four Module Snaptrack-type Bas e for 2MHLP Series

Item#:
DTK-4MB
You must be logged in to order this item. Log in here

12V 100AH BATTERY LI

Item#:
KBC-12100
You must be logged in to order this item. Log in here

Ground Bar for S and SL series protectors

Item#:
DTK-SIGB
You must be logged in to order this item. Log in here

2-Gang, LV Bracket w/Nail, New Const.

Item#:
AC1009-12
You must be logged in to order this item. Log in here

Power over Ethernet (PoE+) Spl itter

Item#:
560443
You must be logged in to order this item. Log in here
|◀ ◀ 1 - 12 of 1213 ▶ ▶|
View:
(Denotes required field.)