Trove2 enclosure with TBH2 Altronix/Bosch backplane:

• Backplane accommodates a combination of Bosch controllers with or without Altronix accessories: B520, B8512G, B9512G, B208, B299, B308, B426, B450, B600, B901, D125B, D129, D132A, D192G, D426, D450, D7412GV4, D8125/MUX, D8128D, D8129, D8130, D9412GV4 & ICP-SDI-9114, Altronix PD16W or PD16WCB Sub-Assemblies
• Includes Altronix Trove2 Enclosure and one (1) removable TBH2 backplane

• 16 AWG backplane.
• Includes mounting hardware.
• Accommodates the following Bosch controllers with or without Altronix accessories: B520, B8512G, B9512G, B208, B299, B308, B426, B450, B600, B901. D125B, D129, D132A, D192G, D426, D450, D7412GV4, D8125/MUX, D8128D, D8129, D8130, D9412GV4 & ICP-SDI-9114, Altronix PD16W or PD16WCB Sub-Assemblies.
• Simplifies board layout and wire management
• 16 AWG galvanized steel

Altronix T2KK3F8DQ is pre-assembled and consists of Trove2 enclosure with factory installed Altronix power supply/chargers, transformer, and sub-assemblies. These kits also accommodates various combinations of Keyscan boards for up to eight (8) doors in a single enclosure.

• Input: 120VAC 60Hz/3.5A.
• Output:
  • 24VDC up to 5.8A max current.
  • Eight (8) Fail-Safe/Fail-Secure Outputs (auto-resettable).
• Fully assembled kit includes:
  • Trove2 enclosure with TKA2 backplane
  • One (1) eFlow6NB - Power Supply/Charger
  • One (1) LINQ2 - Network Communications Module
  • One (1) ACM8CB - PTC Access Power Controller
  • One (1) T16100 Transformer
• Back-up Battery (not included):
  • Capacity: 12AH / 12VDC (Up to 4 within enclosure); 40 AH / 65 AH (requires separate enclosure).
  • Type - Sealed lead acid or gel type.
  • Fuse Rating: 10A/32V.
  • Failover - Upon AC loss, instantaneous.
• Supervision:
  • AC Failure - Form "C" contacts.
  • Battery - Form "C" contacts.
  • Low DC Power Shutdown - Shuts down DC output terminals if battery voltage drops below 71-73% for 12V units and 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
• LED Indicators:
  • Input - 120VAC is present.
  • DC Output - Powered.
  • Battery - Discharged or not connected.

TBL3 backplane allows you the option of drilling your own mounting holes to accommodate the access controller boards, power supplies and accessories to customize your own access system. Trove simplifies board layout and wire management, reducing installation time and labor costs.

• 16 AWG backplane.
• Includes mounting hardware.
• Simplifies board layout and wire management
• 16 AWG galvanized steel

TM400 Enclosure accommodates a combination of the following:

• Up to three (3) MR50.
• One (1) EP1501 or MR51e.
• One (1) EP4502, EP1502, MR52, MR16IN, or MR16OUT.

Input

• Voltage: 120VAC, 60Hz, 7A max.
• Fusing: 5A / 250V.

Output

• Voltage: Factory set: one (1) eFlow6NB at 12VDC and one (1) at 24VDC.
• Current: 6A continuous.
• Maximum Supply Current for Main and Aux. Outputs on eFlow6NB Power Supply boards and ACMS8 Access Power Controllers’ outputs is 5.3A @ 12VDC and 5.6A @ 24VDC.
• Auxiliary: Class 2 power-limited @ 1A (unswitched).
• Other: Overvoltage protection. Filtered and regulated.

Input

• Voltage: 24VDC from eFlow6NB and 12VDC from VR6.
• Fusing: 15A / 32V.

Output

• Voltage: 12 or 24VDC individually selectable.
• Eight (8) selectable 12VDC - 24VDC independently controlled outputs or eight (8) indepently controlled Form “C” relay outputs:
• a) Fail-Safe and/or Fail-Secure power outputs.
• b) Form “C” Relays. 28VAC or VDC @ 2.5A Rated.
• c) Auxiliary power outputs (unswitched).
• d) Any combination of the above.
• Any of the eight (8) fuse protected power outputs are selectable to follow power Input 1 or Input 2.
• Individual outputs may be set to OFF position for servicing.
• Fuses Rating: 2.5A / 32VDC.

Indicators (LED)

• Red LEDs: Outputs are triggered (relays energized).
• Blue LED: FACP disconnect is triggered.

Individual voltage LEDs

• Green: 12VDC
• Red/Green: 24VDC