S2K Commerce - Products Dropdown
S2K Commerce - Shopping Cart
S2K Commerce - Order Entry
Altronix T2MK3F4DQ is pre-assembled and consists of Trove2M2 enclosure with factory installed Altronix power supply/charger(s) and sub-assemblies. This kit also accommodates various combinations of Mercury boards for up to four (4) doors in a single enclosure.
Altronix T2MK3F8D is pre-assembled and consists of Trove2M2 enclosure with factory installed Altronix power supply/charger(s) and sub-assemblies. This kit also accommodates various combinations of Mercury boards for up to eight (8) doors in a single enclosure.
Altronix T2KK3F8 is pre-assembled and consists of Trove2 enclosure with factory installed Altronix power supply/chargers, transformer, and sub-assemblies. These kits also accommodates various combinations of Keyscan boards for up to eight (8) doors in a single enclosure.
- Up to two (2) eFlow4NB, eFlow6NB, eFlow102NB, or eFlow104NB.
- Up to four (4) ACM8(CB) or ACMS8(CB).
- Up to two (2) ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), or VR6.
- Includes Altronix Trove1R Rack Enclosure and one (1) removable TAL1R backplane.
- 16 Gauge black powder coated steel enclosure with ample knockouts for convenient access.
- Includes: tamper switch, cam lock and mounting hardware. Modular 2U standard EIA 19” drawer with extendable slides up to 48”.
- IEC320 connector.
- Included Z Bracket facilitates ease of wiring.
Input
- Voltage: 120VAC, 60Hz, 3.5A max.
- Fusing: 5A / 250V.
Output
- Voltage: Factory set at 24VDC.
- Current: 6A continuous.
- Maximum Supply Current for Main and Aux. Outputs on eFlow6NB Power Supply board, ACMS8 Access Power Controller’s and PDS8 Power Distribution Module’s outputs is 5.6A.
- Auxiliary: Class 2 power-limited @ 1A (unswitched).
- Other: Overvoltage protection. Filtered and regulated.
- Built-in charger for sealed lead acid or gel type batteries (if batteries are required, install separate battery enclosure RE2).
- Automatic switch over to stand-by battery when AC fails.
- Zero voltage drop when unit switches over to battery backup (AC failure condition).
- Supervised: Latching or non latching.
- EOL: 10K Resistor.
- AC Failure: Form “C” contacts.
- Battery: Form “C” contacts.
- Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units. Prevents deep battery discharge.
- Input: 120VAC is present.
- DC Output: Powered.
- Battery: Discharged or not connected.
Input
- Voltage: 24VDC from eFlow6NB and 12VDC from VR6.
- Fusing: 10A / 250V.
Output
- Voltage: 12 or 24VDC individually selectable.
- Fuses Rating: 3A / 32VDC.
Indicators (LED's)
- DC Output: Eight (8) individual output LEDs.
Input
- Voltage: 24VDC from eFlow6NB and 12VDC from VR6.
- Fusing: 15A / 32V.
Output
- Voltage: 12 or 24VDC individually selectable.
- Eight (8) selectable 12VDC - 24VDC independently controlled outputs or eight (8) indepently controlled Form “C” relay outputs:
- a) Fail-Safe and/or Fail-Secure power outputs.
- b) Form “C” Relays. 28VAC or VDC @ 2.5A Rated.
- c) Auxiliary power outputs (unswitched).
- d) Any combination of the above.
- Any of the eight (8) fuse protected power outputs are selectable to follow power Input 1 or Input 2.
- Individual outputs may be set to OFF position for servicing.
- Fuses Rating: 2.5A / 32VDC.
Indicators (LED)
- Red LEDs: Outputs are triggered (relays energized).
- Blue LED: FACP disconnect is triggered.
Individual voltage LEDs
- Green: 12VDC
- Red/Green: 24VDC
Trove3 enclosure with TBL3 backplane:
Trove3 Enclosure:
Altronix T2MK75F16D is pre-assembled and consists of Trove2M2 enclosure with factory installed Altronix power supply/charger(s) and sub-assemblies. This kit also accommodates various combinations of Mercury boards for up to sixteen (16) doors in a single enclosure.
Altronix T2MK77F16Q is pre-assembled and consists of Trove2M2 enclosure with factory installed Altronix power supply/charger(s) and sub-assemblies. This kit also accommodates various combinations of Mercury boards for up to sixteen (16) doors in a single enclosure.