S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
Features:
- The HSM2204 is a dual-purpose module that provides programmable outputs for controlling external devices, and provides an additional +12 V 1.0 A of additional power
- Connect up to 4 modules per system
- Fully supervised for AC failure, low battery and AUX failure
- Compatible with HS2016, HS2032, HS2064 and HS2128 control panels
The Inovonics high power repeater intelligently amplifies transmission from any EchoStream series transmitter while ignoring background noise. The repeater is perfect for large facilities such as multi-floor buildings, multi-building sites, shopping malls, campuses and other open-air installations. Virtually any number of repeaters can be added to a system, scaling the system size as needed.
Features:
- Includes backup battery
- No wires or programming needed
- Self configuring
- Case tamper protection
The ELK-M1XSLU is a dedicated Elk-M1 serial expander for connecting an M1 Control to a Lutron RadioRA2 Main Repeater. RadioRA2 is a wireless multi-room control system for Lights, Shades, and HVAC Thermostats. Interfacing a RadioRA2 system to an M1 allows control in response to security system actions or conditions. With the automation and remote capabilities built into M1 it is possible to control RadioRA2 devices from across the room or across the world. Benefits include energy savings, convenience, and comfort.
The M1XSLU should be mounted as close as possible to the RadioRA2 Main Repeater. An 18 inch 9-pin flat ribbon serial interconnect cable is provided.
Includes:
- M1 to Lutron RadioRA2 Serial Interface
- Plastic Housing
- ELK-W040A DB9 Pin Serial Cable Assembly
- 4 #6 Plastic Anchors
- 4 #6 Pan Head Sheet Metal Screws
- Instructions
- Activity/Status LED (Orange)
- Auto-Reset Hardware Watchdog Circuit
- Addressable (1-7) TYPE 5 Databus ID
- Connection to Main Repeater: RS232 Cable - Included
- Connection to M1: Elevator Screw Terminals (4)
- Operating Voltage: 12 Volts D.C.
- Current Draw: 31mA
- Housing Dimensions: 4.25 in. x 6.375 in. x 2.125 in.
- Circuit Board: 2.75 in. x 3.95 in.
- Can be located anywhere along the two-wire addressable V-Plex® bus
- Converts any conventional detection device to an addressable device. Conventional detector must provide dry-contact output.
- System automatically learns device serial number so no DIP switch addressing is required
- Small size fits easily into most sensing detector enclosures or splice boxes
- Two zone inputs: one supervised with 10K EOL resistor, one unsupervised loop
- Loop 1 provides a broad, 300 ohm tolerance
- Supervised for open, shorted or normal circuit conditions
- UL Listed for commercial burglary and fire alarm applications
- Mounts directly in control panel cabinet using double-sided tape (included)
- Three-wire RS232 or four-wire RS422 interface to external equipment
- Four status LEDs for system troubleshooting
- Driver software is required to use this module; this software is provided separately. To obtain drivers, consult the third party vendor with whom you need to work.
- Can be optionally powered from an external DC power supply to reduce the amount of current draw from the polling loop
- Uniquely identifies eight EOLR supervised zones (all zones use 10K resistors, supplied)
- DIP Switches can be used to set zone numbers or serial numbers
- When used in the serial number mode, each serial number in the selected group can be assigned to any zone number
- Loops A & B can be programmed for fast (10msec) response
- Provides cover tamper protection, which may be enabled or disabled via on-board DIP Switches
S2K Administration - Form Template Display
Actions