S2K Commerce - Products Dropdown
ActionsS2K Commerce - Shopping Cart
ActionsS2K Commerce - Order Entry
ActionsAltronix AL175ULX is a Two (2) Output Switching Power Supply/Charger that converts a 115VAC 60Hz input, into two (2) individually PTC protected 12VDC or 24VDC outputs.
Input
Output
4-Door Expansion Kit. Includes: KT-400 Controller, TR1675 16 VAC/75 VA Transformer & KT-BATT-12 12V 7 AH Battery
The way that the Qolsys IQ Hardwire 16-F works is very simple. It has 16 on-board zone terminal pairs for connecting hardwired sensors. Each zone features its own LED light to assist with enrollment and troubleshooting. A resistor must be used at each zone. In Legacy Mode, the QS7134-840 can be calibrated to use 1k to 10k resistors that are wired in parallel (NO) or series (NC). This differs from the older-style QS7133-840 that was restricted to only supporting 4.7k resistors (Yellow-Violet-Black-Brown-Brown). However, all versions of the Qolsys IQ Hardwire 16-F come with the same 4.7k resistors that must be used to meet UL Standards for fire protection. These resistors work great, so it is advised that you just use the included ones to avoid any possible confusion.
For primary power, the Qolsys IQ Hardwire 16-F uses its included 16VDC transformer. This transformer features an attached power cable for connecting with the module. On the cable, the wire with the grey dashes is the positive (+) connector. The unmarked wire represents the negative (-) connector. If you damage the transformer or the attached cable, then you will need to get a replacement 16VDC transformer.
- Emergency Exit Buttons offer additional safety, as required by code, for possible malfunction of motion exit sensor
- Mounted next to door
- Momentarily pressing the button releases door for 30 seconds
- Retriggerable
- Single Gang or Narrow Stile
- SPST 3 Amp wet N/C contacts
- Operates on 12 or 24 VDC (must be same voltage as the installed lock)
- For indoor use only
- Includes switchable green, red and blue ADA lenses
- UL Listed
Features
- Full online and offline operation
- Supports for 30,000 active credentials, 30,000 PIN codes, 128 access groups, 128 access areas, 128 time zones, 64 holidays and 32 NG Smart Links for automation
- 20,000 nonvolatile, FIFO, records the event log while offline
- Expandable with MD-IO84B I/O expansion for additional 8 inputs, 4 outputs OR the MD-D02B 2-Reader expansion for additional 2 readers with 4 inputs, 4 outputs
- Real-time clock with super-cap holds power and keeps RTC real-time clock for up to 2 weeks when total power loss (no batteries to replace)
- Supports wide range of Wiegand reader formats, PIN keypad formats, and logic options to support wide range of locks, deadbolts, electric strikes, maglocks, and sliding doors
This is a credit-card sized credential with RFID electronics built inside the card, including an integrated circuit and an antenna inside that can be printed for human-readable information using standard ISO card printers, which can be machine read using very low power wireless communications. Having no power of its own, it can be read by card readers when it passes through the electromagnetic field produced in the proximity of the reader. The range depends on the antenna and field generated by the reader, so the card will have different read-ranges.
- Users/Fingerprints: 5000 Event Buffer:10,000 Reader
- Ports:4 (Support multi format Weigand or OSDP Readers)
- Communication: TCP/IP/Wifi and RS485 for FP and OSDP Readers
- Input Ports: 9 (4 exit buttons, 4 door sensors, 1 Aux Input)
- Output Ports: 5 (4 FORM-C Relay Output for lock and 1 Aux Output Relay)
- Gross Weight: 3 lbs.
- Package Size: 12" x 9" x 4"