|◀ 217 - 228 of 16556 ▶|
View:
You must be logged in to order this item. Log in here

Altronix AL175ULX is a Two (2) Output Switching Power Supply/Charger that converts a 115VAC 60Hz input, into two (2) individually PTC protected 12VDC or 24VDC outputs.

Input

  • Input 115VAC, 60Hz, 0.6A.
  • Access control trigger input.
Output
  • 12VDC or 24VDC selectable outputs.
  • 1.75A supply current.
  • Two (2) Class 2 Rated power limited outputs.
  • Fail-Safe/Fail-Secure lock output (switched).
  • Auxiliary power output (unswitched).
  • PTC protected outputs, rated @ 2.5A.
  • Filtered and electronically regulated output.
  • Short circuit and thermal overload protection.

Item#:
AL175ULX
You must be logged in to order this item. Log in here

  • As with other Indala credentials, the FlexKey is compatible with all Indala readers, and can be easily encoded with the Indala ProxSmith® Programmer and toolkit.
  • This RF programmable, 125 kHz tag offers a consistent read range and is unaffected by body shielding or variable environmental conditions.
  • The passive, no-battery design allows for an infinite number of reads.
  • FlexKey Flexibility and Convenience - Contemporary design enables it to be easily attached to a key, badge clip, or badge lanyard.
  • Rugged, Double-Sealed Construction - FlexKey is built to withstand harsh operating environments.
  • Customizable - FlexKey can be customized by adding a company logo.

Item#:
FPKEY-SSSS-0000
You must be logged in to order this item. Log in here

4-Door Expansion Kit. Includes: KT-400 Controller, TR1675 16 VAC/75 VA Transformer & KT-BATT-12 12V 7 AH Battery

Item#:
EK-400
You must be logged in to order this item. Log in here
The Qolsys QS7134-840 IQ Hardwire 16-F w/ Large Enclosure is a wired to wireless system converter that transmits signals at the 319.5 MHz frequency. By using this module, you can bring over your existing hardwired sensors and use them with your 319.5 MHz wireless security system.

The way that the Qolsys IQ Hardwire 16-F works is very simple. It has 16 on-board zone terminal pairs for connecting hardwired sensors. Each zone features its own LED light to assist with enrollment and troubleshooting. A resistor must be used at each zone. In Legacy Mode, the QS7134-840 can be calibrated to use 1k to 10k resistors that are wired in parallel (NO) or series (NC). This differs from the older-style QS7133-840 that was restricted to only supporting 4.7k resistors (Yellow-Violet-Black-Brown-Brown). However, all versions of the Qolsys IQ Hardwire 16-F come with the same 4.7k resistors that must be used to meet UL Standards for fire protection. These resistors work great, so it is advised that you just use the included ones to avoid any possible confusion.

For primary power, the Qolsys IQ Hardwire 16-F uses its included 16VDC transformer. This transformer features an attached power cable for connecting with the module. On the cable, the wire with the grey dashes is the positive (+) connector. The unmarked wire represents the negative (-) connector. If you damage the transformer or the attached cable, then you will need to get a replacement 16VDC transformer.
Item#:
QS7134-840
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

  • Emergency Exit Buttons offer additional safety, as required by code, for possible malfunction of motion exit sensor
  • Mounted next to door
  • Momentarily pressing the button releases door for 30 seconds
  • Retriggerable
  • Single Gang or Narrow Stile
  • SPST 3 Amp wet N/C contacts
  • Operates on 12 or 24 VDC (must be same voltage as the installed lock)
  • For indoor use only
  • Includes switchable green, red and blue ADA lenses
  • UL Listed
Item#:
EEB2
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

The heavy duty GL1 Electromechanical Gate Lock provides weather-resistant access control for a wide range of gate applications. The GL1 provides 2000lbs of holding force for electrical and manually operated indoor or outdoor gates where preload is a concern. Ideal for swinging or sliding Product features vehicle, pedestrian, or stock gate access control.

Features

  • 2,000 lbs holding force
  • Operates under preload up to 100lbs
  • Automatic dual voltage - no field adjustment required
  • Accepts a standard mortise cylinder with Adams Rite MS cam for manual key override (not included, see spacer guide below)
  • Self-aligning receiver (+/- 1/2 in. horizontally) helps compensate for gate misalignment and sag
  • Tamper resistant cast housing
  • Optional latch status monitor
  • Surface mount
  • MagnaCare lifetime replacement, no fault warranty

Item#:
GL1-FS
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

AL600ULX is a power supply/charger which converts a 115VAC/60Hz input into a single 12VDC or 24VDC non power-limited output.

Input

  • Input 115VAC, 60Hz, 3.5A.
Output
  • 12VDC or 24VDC selectable output.
  • 6A continuous supply current.
  • Filtered and electronically regulated output.
  • Short circuit and thermal overload protection.

Item#:
AL600ULX
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
|◀ 217 - 228 of 16556 ▶|
View:
(Denotes required field.)