The MMF-300 Monitor Module is intended for use in intelligent, two-wire systems, where the individual address of each module is selected using the built-in rotary switches. It provides either a two-wire or four-wire fault-tolerant Initiating Device Circuit (IDC) for normally-open-contact fire alarm and supervisory devices. The module has a panel-controlled LED indicator. The MMF-300(A) can be used to replace M300 modules in existing systems.

Features

• Built-in type identification automatically identifies this device as a monitor module to the control panel.
• Powered directly by two-wire SLC loop. No additional power required.
• High noise (EMF/RFI) immunity.
• SEMS screws with clamping plates for ease of wiring.
• Direct-dial entry of address: 01  159 on MS-9600 series panels, 01  99 on other compatible systems.
• LED flashes during normal operation and latches on steady to indicate alarm.

The SK-MONITOR-2 is an addressable monitor module with two initiating circuits that act as an interface to dry contact devices such as waterflow switches and conventional pull stations.

Features

• Monitor two circuits with unique addresses simultaneously
• Rotary address switches for fast installation
• Support for Class B wiring
• Bright white cover plate
• SEMS screws for easy wiring
• UL listed

MDF-300 Dual Monitor Module The MDF-300(A) Dual Monitor Module is intended for use in intelligent, two-wire systems. It provides two independent twowire initiating device circuits (IDCs) at two separate, consecutive addresses. It is capable of monitoring normally open contact fire alarm and supervisory devices. The module has a single panelcontrolled LED.

The SD500-MIM is an addressable mini-input module that acts as an interface to dry contact devices such as waterflow switches and conventional pull stations. Due to its small size the SD500-MIM can be mounted in a single gang junction box directly behind the monitored device.

Features

• Single contact monitor
• Support for Class B wiring
• Small and lightweight size allows for flexible mounting options
• DIP switch programming for fast installation
• UL listed

MS-5UD-3 is a five zone conventional fire control panel has features normally found in more expensive addressable systems. The MS-5UD-3 is fully programmable via built-in keypad and 80 character LCD display, so you do not need an external programmer. The five zones panel has a built-in Digital Alarm Communicator Transmitter (DACT) and availability to add optional equipment: Remote annunciator, Relay module, LED Driver module, Transmitter module and Printer interface module.

Features

• Five-zone Style B (Class B) or Five-zone Style D (Class A) with optional module
• Four NAC Circuits Style Y (Class B) or Four NAC Circuits Style Z (Class A) with optional modules
• Built-in NAC synchronization for System Sensor, Wheelock, Gentex, Faraday and Amseco devices
• Integral 80 character LCD display with backlighting and keypad
• Annunciator bus supports up to 8 devices, including ANN-80 LCD Remote Annunciator, ANN-S/PG remote serial or parallel printer gateway, ANN-RLY, 10 form C relay board, ANN-LED Zone annunciator and ANN-I/O LED driver board for graphic annunciators
• Built-in two-line digital communicator for off premises monitoring
• Three Form-C programmable relays
• 3.0 amps total usable current

The SK-CONTROL is an addressable notification module and provides supervised monitoring of wiring to the load devices that require an external power supply to operate such as bells, horns, and strobes.

Features

• Flexible solution for adding notification circuits where needed
• Rotary address switches for fast installation
• Support for Class B (Style Y) or Class A (Style Z) wiring
• Bright white cover plate
• Polling LED visible through the cover plate
• Compatible with version 10 and higher 5700, 5808, 5820XL, and 5820XL-EVS IntelliKnight addressable fire alarm control panels programmed for System Sensor protocol
• UL listed

The SD500-ANM is an addressable notification module and provides supervised monitoring of wiring to the load devices that require an external power supply to operate such as bells, horns, and strobes.

Features

• Flexible solution for adding notification circuits where needed
• DIP switch programming for fast installation
• Support for Class B (Style Y) or Class A (Style Z) wiring
• Attractive ivory cover plate
• Polling LED visible through the cover plate
• UL listed