The ELK-965 is a Low Battery Cutoff Module combined with a Master Power Switch. It is designed to work with virtually any 12 Volt control panel or power supply. In the event of an extended power outage, the ELK-965 sensing circuit automatically disconnects the battery when the voltage falls below 10 Volts DC. This helps to prevent "deep discharging" of the battery. The convenient power switch permits the installer or user to easily disconnect both the Battery and the AC power from the control or power supply.
Includes:

• 1 Low Battery Cutoff & Master Power Switch
• 2 pieces of Double Sided Tape
• Instructions

To enable the Image2 on a GC3 panel, the new Image Sensor Adapter ( 2GIG-XCVR3-GC3) is required to be installed, as well as Firmware version 3.0.1 or newer.

• NEW StarLink Connect Honeywell Upload Download Model
• Easy-to-Install Cellular-based communicator – Requires No Internet Connection at Premises
• Dual Path, IP & Cellular with optional Wi-Fi
• Upload / Download to Honeywell panels using native Compass download software
• Upload / Download to DSC panels using native DLS download software

The 2GIG 4Button Keyfob Remote communicates with the 2GIG Control Panel on the 345 MHz frequency. It gives users the ability to turn the security system ON and OFF before entering the home or after exiting. If there is an emergency, you can turn on the siren and automatically call the central monitoring station. Keyfobs can be programmed to operate the programmable output in the Control Panel. Use with the 2GIG Universal Garage Door Receiver (2GIGGDR1345) to open a garage door. The keyfob is a lithium coin batterypowered, wireless keyfob designed to fit on a key chain, in a pocket, or in a purse.

Features:

• Arms system in STAY or AWAY mode
• Disarms system
• Auxiliary output and emergency functions
• Lithium coin battery with 5 years life

Altronix SMP3 power supply/charger converts a low voltage AC input into a 6VDC, 12VDC or 24VDC output. This unit has a wide range of applications for access control, security and CCTV system accessories that require additional power.

Features:

• Extremely compact design.
• Includes battery leads.
• Snap Track compatible (order Altronix model number ST3)

The 2GIG-FT1-345 is a fully supervised, tamper protected one-way 345 MHz sensor. It will monitor the ambient temperature and will detect a wet/dry flood condition. The sensor reports wet/dry conditions and temperature to the panel.

Once the sensor probe detects the presence of water for three (3) minutes, the integral transmitter will send a wet alarm transmission to the security/control panel. The probe will also send a restore (dry) report when the presence of liquid is no longer detected by the flood probe for three (3) minutes. For flood reporting, the sensor requires the installation of the supplied external flood probe. The sensor is capable of detecting clean or dirty fresh water, salt water, or tap water.

Features:

• Detects standing water that reaches the sensor probe and notifies the panel
• Sends trouble alert to the panel when the ambient temperature exceeds 84 deg. F
• Sends trouble alert to the panel when the ambient temperature falls below 42 deg. F
• Ships with long life lithium battery life (typical battery life of 5 years)
• ETL listed
• Requires Firmware Version 1.14 or later for GC2 panel and 3.1 or later for GC3

• Easy-to-Install Cellular-based Connected Home Communicators – Requires No Internet Connection at Premises Dual Path, IP & Cellular with optional Wi-Fi
• Upload / Download to NAPCO, Honeywell and DSC control panels
• Virtual Keypad control of NAPCO, Honeywell and DSC control panels
• iBridge Messenger Notifications for NAPCO, Honeywell and DSC control panels

The Model 2GIG-UPDV Easy Updater for GC2 and TS1 allows you to quickly and easily update a GC2 panel or TS1 keypad without using a computer or incurring the OTA update charges from your backend service provider. The compact design of the Easy Updater fits in a technicians toolbox and ships with firmware already installed for instant use right out of the box. It is ideal for a tech who is updating a system from a 2G radio on previously installed panels. Just update the panel using the Easy Updater and replace the old radio.

Features

• No batteries required, powered by the panel
• 4-Position LED Display for easy status updates
• Micro USB Socket for firmware upgradeability
• Start button to initiate the GC2 or TS1 firmware upgrade
• Sounder for status change notifications
• 4-Pin Adapter for early TS1 production model
• Durable, compact enclosure
• LED to indicate correct cable connection

The Model HUB-M (2020130) provides momentary or latching DPDT contacts for actuating surveillance cameras or other security applications.