MDF-300 Dual Monitor Module The MDF-300(A) Dual Monitor Module is intended for use in intelligent, two-wire systems. It provides two independent twowire initiating device circuits (IDCs) at two separate, consecutive addresses. It is capable of monitoring normally open contact fire alarm and supervisory devices. The module has a single panelcontrolled LED.

The MMF-300 Monitor Module is intended for use in intelligent, two-wire systems, where the individual address of each module is selected using the built-in rotary switches. It provides either a two-wire or four-wire fault-tolerant Initiating Device Circuit (IDC) for normally-open-contact fire alarm and supervisory devices. The module has a panel-controlled LED indicator. The MMF-300(A) can be used to replace M300 modules in existing systems.

Features

• Built-in type identification automatically identifies this device as a monitor module to the control panel.
• Powered directly by two-wire SLC loop. No additional power required.
• High noise (EMF/RFI) immunity.
• SEMS screws with clamping plates for ease of wiring.
• Direct-dial entry of address: 01  159 on MS-9600 series panels, 01  99 on other compatible systems.
• LED flashes during normal operation and latches on steady to indicate alarm.

Addressable Mini-Monitor Module, One Style B (Class B) Initiating Device Circuit for Monitoring N/O contact devices, does not include a polling LED

The MMF-301 monitor module can be installed in a single gang junction box directly behind the monitored unit. Its small size and light weight allow it to be installed without rigid mounting. The MMF-301 is intended for use in intelligent, two-wire systems where the individual address of each module is selected using rotary switches. It provides a two-wire initiating circuit for normally open contact fire alarm and security devices. This module can be used to replace an M301 module in existing systems.

MMF-300(A) is a standard-sized module that supervises either a Style D (Class A) or Style B (Class B) circuit of dry-contact input devices.

The CRF-300 Addressable Relay Module provides the system with a dry-contact output for activating a variety of auxiliary devices, such as fans, door holders, dampers, control equipment, etc. Addressability allows the dry contact to be activated through panel programming, on a select basis. LiteSpeed is a communication protocol developed by FireLite Engineering that greatly enhances the speed of communication between analog intelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the panel CPU stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of other designs.

Features

• Built-in type identification automatically identifies these devices to the control panel.
• Internal circuitry and relay powered directly by two-wire SLC loop.
• Integral LED blinks green each time a communication is received from the control panel and turns on in steady red when activated.
• High noise immunity (EMF/RFI).
• Wide viewing angle of LED.
• SEMS screws with clamping plates for wiring ease.
• Direct-dial entry of address: 01 159 for MS-9600(A) series

The EVS-50W is an intelligent 50 watt amplifier for use with version 14.0 or newer 5820XL-EVS. The EVS-50W is used to amplify audio messaging throughout an area or facility. The EVS-50W is capable of producing 50 watts of audio power over 4, expandable to 8, fully programmable speaker circuits.

Features

• 50 watts of audio power
• Comes with 4 fully programmable Class A or Class B speaker circuits
• 25 or 70.7 Vrms operation
• Expansion up to 8 speaker circuits with the EVS-CE4
• Six wire connection to the 5820XL-EVS system: two wires for the Voice Bus (VBUS) and four wires for the SBUS connections
• Can be mounted up to 6000 feet away from the 5820XL-EVS control panel
• 120 VAC or 240 VAC operation
• UL 864 and UL 2572