|◀ ◀ 1 - 12 of 219 ▶ ▶|
View:

Hold Up Button, Momentary, SPDT, 3 Screw Terminals

Item#:
HUB2SA
You must be logged in to order this item. Log in here

Hold Up Button, Latching, DPDT, 3 Screw & 3 Solder Terminals

Item#:
HUB2A
You must be logged in to order this item. Log in here

GD-2B-Methane & Propane - Comb ustible Gas Detector for use w

Item#:
GD-2B
You must be logged in to order this item. Log in here

EnviroAlert Two Zone (12 VDC) Temp, Humidity, and Water Sensor

The EnviroAlert EA-200 critical-environment monitoring device provides visibility to 2 environmental factors: ambient temperature and an additional factor of temperature, humidity or water presence. In addition to the local (on device) visual and audible notifications, when integrated to a security panel the system allows for the real-time notification of an incident and immediate corrective action.

Features:

  • Simultaneous operation of two sensors
  • Easy to read LCD display
  • 8 event incident memory, including time and date
  • Auxiliary output relay for local audible alarm
  • Auxiliary alarm silence feature with 10 minute timer
  • Offset sensor calibration adjustment
  • Tamper proof lock setting
  • Alarm notification via dry contact relay to any alarm panel

Item#:
EA200-12
You must be logged in to order this item. Log in here

Hold Up Button - Momentary, DP DT, 3 Screw & 3 Solder Termina

Item#:
HUB-3A
You must be logged in to order this item. Log in here

Hold Up Button - Momentary, DP DT, 6 Screw Terminals

Item#:
HUB-3B
You must be logged in to order this item. Log in here

20' Indoor Curtain PIR

Item#:
AP2-20N
You must be logged in to order this item. Log in here

Water Shutoff Valve 1" - NPT 12VDC

Item#:
ELKWSV3
You must be logged in to order this item. Log in here

Long Life Door/Window

The Alula DWS-LL is an encrypted, LongLife, wireless door or window sensor designed to be used with the Alula Connect+ Panel. The DWS-LL sensor detects opening and closings of doors and windows. It can secure just about anything that opens with its simple peel-and-stick mounting solution. The DWS-LL will alarm, when the Connect+ Panel is armed and the magnet is pulled away from the contact.

To enroll the DWS-LL, begin by placing the panel into wireless enrollment mode and then sending an enrollment signal from the LongLife sensor. Alternatively, the LongLife sensor can be enrolled by scanning its bar code using the Alula app or by entering its 8-character serial number on the interactive GeoArm web portal.

To install the DWS-LL, begin by removing the adhesive paper and adhering the LongLife contact and magnet on a door or window. Clean the surface of where you plan on mounting it. Leave a minimum of 3/16 inch clearance around the ends of the sensor to allow the cover to open. Make sure to align the alignment marks on the LongLife and magnet when mounting. Alternatively, LongLife can be used with an external contact instead of the reed switch.

The High Bond Tape (3M VHB Tape) works great if the surface is properly prepared and firm pressure is applied for over 10 seconds. The LongLife wireless performance is optimized when mounted near the top of the door in a vertical orientation.

Product Features:
  • Low-profile design
  • Easy, slide-open cover
  • Battery pull-tab enrollment
  • 5-year product warranty
  • 10-year battery life (replaceable) 
Item#:
DWS-LL
You must be logged in to order this item. Log in here

Hold Up Button, Latching, DPDT, 6 Screw Terminals

Item#:
HUB2B
You must be logged in to order this item. Log in here

Hold Up Button - Latching, DPD T, 6 Solder Terminals

Item#:
HUB2
You must be logged in to order this item. Log in here

Metal Latching Hold Up-Switch

The HUSK-20 is a mechanical hold-up switch designed for silent operation. It is activated by using one finger to press down on the switch.
When activated, the switch mechanism locks, insuring an immediate alarm signal. A status window designed on top of the hold-up switch indicates its condition: RED (alarmed) and BLUE (armed). To reset the HUSK-20, use the key provided. The housing is made of metal and is painted gray.
The hold-up switch sends a signal to a dedicated 24 hour hold-up circuit of a burglar control panel. That signal in turn will send the immediate signal to police or central station.

Features:

  • Form C contact
  • Metal housing
  • Key reset
  • Silent operation
  • Status window indicator (armed, alarmed)
  • Mechanical operation
  • Terminals for easy wiring

Item#:
4370038
You must be logged in to order this item. Log in here
|◀ ◀ 1 - 12 of 219 ▶ ▶|
View:
(Denotes required field.)