|◀ 13 - 24 of 43 ▶|
View:
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

  • Add up to 32 high performance EchoStream wireless transmitters to any installation
  • Includes support for both single and multiple condition transmitters
  • Two line text display shows condition of each transmitter, provides log of past events, and displays signal strength
  • Outputs can be configured in follower, latching, momentary, or toggle modes independently
  • Case tamper protection, jam detection, and internal antennas for a secure wireless implementation
  • Wireless programming routine built into the receiver
  • Includes support for both single and multiple condition transmitters
Item#:
EN4232MR
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

Z-Wave Garage Door Opener Remote Controller

This item has been discontinued and replaced by item 
Item#:
GD00Z-5
You must be logged in to order this item. Log in here

The Model 302850 2-Channel, 12-24V, Gate Receiver is designed for use in gate operator applications. An 11-inch wire whip antenna is included for local reception. The whip antenna connects to the receivers Type-F antenna connector. Also included is 3-feet of coax cable and a bulkhead connector for remotely mounting the whip antenna in installations where the receiver is mounted inside a shielded metal enclosure, such as a gate operator housing. An external Model 106603 Remote Whip Antenna can also be used with this receiver.

The Model 302850 is a dual frequency receiver. An internal jumper selects either 300 MHz or 310 MHz operating frequency. The 300 MHz frequency is compatible with standard Multi-Code transmitters, the 310 MHz frequency is compatible with the Stanley version Multi-Code transmitters.

The operator supplies 12-24 volt power to the receiver, or the receiver can be powered by a separate AC power transformer or DC power supply. The normally open relay outputs can switch up to 1 amp @ 30 VAC. 3-foot, 2-conductor wire leads with spade lugs are provided for attachment to the gate operators radio activation terminals.

The receiver is programmed with a 9-position coding switch. When a transmitter set to the same code is activated, the receivers output will activate, triggering the gate operator. Transmitter switch #10 selects which receiver channel will activate.

  • Operates on 12-24 volts AC or DC power
  • Two channels
  • Whip antenna
  • 3-foot antenna coax and bulkhead connector
  • Codes: 512 (set by dip switches)
  • RF frequency: 300 MHz or 310 MHz (jumper selectable)
  • Dimensions: 3.625" W x 5.25" H x 1.5" D

The Model 302850 is compatible with Multi-Code and Stanley Multi-Code transmitters only.

Item#:
MCS302850
You must be logged in to order this item. Log in here

Commercial Fire and Burg approved Wireless Receiver, supports 255 devices, max of (4) receivers supported by GEM-C system.

Item#:
GEMC-RECV
You must be logged in to order this item. Log in here

RF Crystal Rec, 2 Antenna, GE

This item has been discontinued and replaced by item 
The ELK-M1XRFEG is a Wireless (RF) Receiver and Input Expander for use with the ELK-M1 and ELK-M1EZ8 Controls. The receiver connects to the four (4) wire data (keypad) bus of the control and integrates in much the same way as a M1XIN hardware zone expander except that a single M1XRF can handle up to 144 wireless zones (e.g. transmitter sensors or points).
The M1XRFEG receiver is a dual (2) antenna, phase diversity design capable of long range wireless coverage. It is compatible with ELK's 319 Series Wireless Sensors, as well as other 319.5MHz sensors (Interlogix format).
  • Adds up to 144 individual wireless zones (sensors/points) 
  • Operates from the 4 wire RS485 Data Bus 
  • Additional Receivers (up to 9) may be Connected to a single M1 or M1EZ8 Control for redundancy or greater coverage 
  • Flash Memory for Updating of operating Firmware 
  • Sensitivity: >105 dbm 
  • Operating Temperature: 0 to +120 degrees F 
  • Operating Voltage: 12 Volts D.C. 
  • Current Draw: 70mA 
  • Range: 300 to 500 ft. line of sight 

NOTE: Walls or metal may reduce actual operating range.
Item#:
M1XRFEG
You must be logged in to order this item. Log in here

Z-Wave Battery Powered Thermostat

This item has been discontinued and replaced by item 

  • Battery powered design runs on 4 “AA” batteries
  • Extremely long 2 year battery life
  • Can be powered by 24 VAC “C” wire from HVAC system
  • Z-Wave compatible – Ver. 4.5.5
  • Supports Z-Wave FLiRS functionality
  • Works on standard HVAC systems: 2 stage heat/ 2 stage cool
  • Works on heat pump HVAC systems: 3 stage heat/ 2 stage cool
  • Incredibly easy to install and program
  • USB firmware upgrade ability
  • Wall mount or mounts on single-gang junction box
Item#:
GC-TBZ48
You must be logged in to order this item. Log in here
Compatible with HS2016, HS2032, HS2064 and HS21218 control panels.  *Note - Only keypad version 1.4 or higher is compatible with PowerSeries Pro.
Item#:
HS2LCDWFP9 N
You must be logged in to order this item. Log in here
|◀ 13 - 24 of 43 ▶|
View:
(Denotes required field.)