S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
An "active" RS-485 data bus hub designed for jobs where an M1Gold or M1EZ8 Control is retrofitting an older panel that has multiple homerun 4 conductor keypad/data wires. It splits the main 485 data bus into 4 managed 485 branches. Each branch can have 2 parallel home run cables for a total of 8 home runs. The end of each cable is EOL terminated to insure proper operation and supervision.
Includes:
- ELK-M1DBHR Data Bus Hub
- ELK-SWG Circuit Board Mounting Glides
- Instructions
- Splits The Controls' RS-485 Data Bus Output Into 4 Managed Branches
- Each Managed Branch Can Have 2 Parallel Home Run Cables (Total Of 8 Home Runs)
- EOL Termination Of Each Branch Insures Proper Operation And Supervision
- Works With Std. 4 Conductor Home Run Wire
- An Additional Unit May Be Connected In Parallel To The Control For Expanding Total Capacity
- Includes Mounting Rails for ELK-SWB Boxes
- Inputs: Elevator Screw Terminals, 4 Position
- Output: Elevator Screw Terminals, 4 Position
- Circuit Board Dimensions: 4.9 in. x 2.75 in.
Item#:
M1DBHR
You must be logged in to order this item.
Log in here
The M1XSLZW is a specialized Elk-M1 serial expander for connecting an M1 Control to Z-Wave enabled devices through a Leviton VRC0P+3 Z-Wave Serial Interface. Z-Wave is a wireless, low power, "mesh" network technology widely used for automating devices such as: Lights, Thermostats, Electronic Locks, etc. Z-Wave empowers devices to be remotely controlled from across the room or across the world with benefits such as energy savings, convenience, and comfort.
The VRC0P+3 is known as a Z-Wave Secondary Controller. It must be included as a permanent member of the Z-Wave network as its job is to maintain contact with all Z-Wave devices. It communicates via RS232 to the M1XSLZW which translates the protocol into the M1 control. This allows commands to be sent and received on the Z-Wave network.
- Activity/Status LED (Orange)
- Auto-Reset Hardware Watchdog Circuit
- Addressable (1-7) TYPE 5 Databus ID
- Connection to VRC0P+3: DB9M 9 Pin Port
- Connection to M1: Elevator Screw Terminals (4)
- Operating Voltage: 12 Volts D.C.
- Current Draw: 31mA
- Housing: 4.25" x 6.375" x 2.125"
- Circuit Board: 2.25" x 3.95"
Item#:
M1XSLZW
You must be logged in to order this item.
Log in here
Access Add-on 2 door plugin PCB for expansion of door capacity
Item#:
GEM-2D
You must be logged in to order this item.
Log in here
The ELK-M1PCSPIM is a special Powerline Interface Module containing a built-in M1XSP Serial Port chip. This all-in-one device makes it easy to permanently connect the ELK M1 Control to a UPB network. Simply locate a convenient unused AC Power Outlet, connect a cable from the M1 data bus to the four (4) terminals on the ELKM1 PCSPIM, and perform an M1 data bus enrollment. The long distance capability of the M1 data bus makes it possible to locate the ELKM1 PCSPIM virtually anywhere, without a lot of complex or ugly cabling or connections. UPB utilizes the AC wiring circuit for transmission, without new or additional wiring, and without radio frequency signals.
- All-in-one device for interfacing M1 with UPB.
- Compact interface requires small amount of space
- Easy hookup - requires only the 4-wire data bus connection. * NO 9-Pin Serial Cable *
- Includes UPB Status light (multicolored) AND a M1 Data Bus Status Light (Green) -- enhances the ability to diagnose and troubleshoot
- Lower cost than purchasing separate and M1XSP and PCSPIM products.
- Removable 4-pin terminal block connection
- Power:
- -UPB Network circuitry – powered from the AC "Primary" Line.
- -M1 Data Bus Device circuitry – powered (12VDC) from the M1 Data Bus (+) & (-) terminals.
- NOTE: Loss of AC primary power should not result in a missing data bus device trouble.
- Current Draw from M1: ~30mA @ 12 VDC
- M1 Bus Device Address: Preset at Address #7 [Requires bus module enrollment]
- Firmware required: 1.0.42 (std. firmware) or later
Item#:
M1PCSPIM
You must be logged in to order this item.
Log in here
The ELK-M1KP is an addressable LCD Keypad for M1 Controls. It features a 32 character, backlit display with adjustable intensity and extra large character fonts, improving readability. Six (6) function ("F") keys can be programmed to contact emergency services or perform tasks; such as, controlling lights, watering the lawn, closing or opening the garage door, etc. The ELK navigation keys easily guide you through the full list of automation tasks, programming, systems diagnostics, and more. An optional plug-in proximity reader is available allowing prox card or fob arming, disarming, door strike control, etc. The fold down door features magnetic closure and can be completely removed, if desired.
- Backlit, Large Character LCD Display, 16 x 2 lines
- Blue LCD Display
- Six (6) programmable function keys
- Unique Menu Navigation/Direction keys
- Adjustable volume for tones/chime
- Accepts Plug-in Proximity Reader (ELK-M1PR) or "External" 26 bit Wiegand Prox Reader
- Built-in Temperature Sensor
- Input for 1 Supervised Zone
- One Programmable "Switched Positive" Voltage Output
- Exit, Stay, Chime, and Bypass Keys
- Programmable display of time, date, & temperature
- Displays system diagnostics and settings
- Input Connection: 6 Pin Plug-In "Flying Lead" Connector (Included)
- Operating Voltage: 13.8 Volts DC
- Current Draw: 40-50mA Idle (low backlight, sound silent) 160mA fully active
- Color: White
- Size: 6.875" x 5.25" x 1.375"
Item#:
M1KPB
You must be logged in to order this item.
Log in here
May be plugged directly into an M1G, M1EZ8, M1XOV, or M1XOVR to convert the voltage outputs into SPDT relays rated for 7A @ 30 VDC, 10A @ 125 VAC.
- 8 Form "C" Relays, SPDT Dry Contact
- Heavy Duty Contact Rating
- Low Current Draw.
- Great For General Purpose Switching.
- Plug-in "Removable" Terminal Blocks
- LED Status Indicators on all 8 Relays
- Twelve (12) Conductor Plug-in Wire Harness
- Mounts in Enclosure using ELK-SWG Glides
- Diode Protection Across Relay Coil.
- Contact Ratings: 7 Amps @ 28 VDC, 10 Amps @ 125 VAC
- Wire Harness Length: 24"
- Operating Voltage: 12 Volts DC Nominal
- Current Draw: 0 mA idle, 250 mA Max.
- Size: 6" x 3.25" x .75" H
Item#:
M1RB
You must be logged in to order this item.
Log in here
S2K Administration - Form Template Display
Actions
(Denotes required field.)