Adds 16 hardwired zones (EOL resistor supervised) to the M1 Gold or M1EZ8 Controls. Operates from 4-wire data bus. Up to 12 of these can be used, increasing total zones (inputs) to 208.
Includes:

• 16 Zone Input Expander
• ELK-SWG Circuit Board Mounting Glides 2/pack
• 18 2200 Ohm Resistors
• Instructions

The GEMC-BSLC-4PT is four point expansion module. Terminals are provided for four supervised zones supporting normally-closed or normally-open contacts. Each expansion module has a unique factory-programmed code (printed on the circuit board and on a label located on the rear case) that distinguishes itself to the receiver

• Single timed output
• Double pole, double throw
• Adjustable sensor sensitivity
• Adjustable relay time: 1/2-15 seconds
• Manual trip test button
• Supports any sensing device with N.O., dry, floating relay contact
• Supports up to 4 sensor probes
• Supports up to 12 sounders
• Includes 12-volt transformer
• Metal enclosure dimensions: 5.5″ x 5.5″ x 2″
• Circuit board dimensions: 4.25″ x 3.25″
• Circuit board (called CT-3B) may be purchased without enclosure
• CT-3BG is conformal coated circuit board for free exit
• Part of the DriveGuard, DriveGuard Integrator, and Pioneer Free Exit systems

The GEMC-BSLC-RLY "Non-Polarized" Single Point Relay Module is a low-current Form C relay interface accessory. The GEMC-BSLC-RLY provides a dry contact relay output for controlling bells, door latches, lights, strobes and other similar Burglary and Home Automation devices.

The GEMC-BSLC-RLY Relay Module connects onto the SLC Bus (polling loop terminalson the GEMC-BSLC board) along with such other accessories as GEMC-BSLC-1PT and GEMC-BSLC-4PT modules.

The GEMC-BSLC-RLY is easy to install--when wiring to the polling loop, the terminals (4 and 5) are non-polarized and so can be connected to either side of the SLC loop. Up to 88 GEMC-BSLC-RLY units may be used with any one Gemini C-Series control panel. Based on the available current the GEMC-BSLC provides, up to 44 GEMC-BSLC-RLY modules may be used with any one GEMC-BSLC.

The first 40 External Outputs (1-40) of the Gemini C-Series control panels are supervised Form C relay contacts (the position of the relay is supervised, but the external relay output wiring is not supervised for opens or shorts). Due to relay supervision, reporting and disabling options, we recommend these first 40 outputs be reserved for controlling Fire devices. Devices addressed as 41-88 are not supervised (do not have a local or remote trouble indication) and thus are for supplementary use only. For UL installations, the external device must be mounted no greater than 3 feet from the GEMC-BSLC-RLY module with no intervening walls or barriers. Refer to the control panel installation instructions for wiring requirements in UL-listed applications.

Features:

• Communication and operating power received from the control panel via the addressable polling loop
• Electronics enclosed within a easy to install plastic case
• Approved for Commercial Burglary and Residential Burglary installations. Note: For Commercial applications, the GEMC-BSLC-RLY module must be installed within a UL-Listed tamper-protected enclosure (i.e. GEMC-HSKIT12V-R, GEMCHSKIT12V-CF or CI-HSKIT12V UL Listed Enclosure Subassembly with GEMC-TAMPERKIT).

The ELK-M1EZ8MSI Main Serial Port Interface allows direct RS-232 Serial Communications to an M1EZ8 Control for Upload/Download programming, and for interfacing with other Computer type devices. Also required when adding the M1XEP Ethernet Port to an M1EZ8 Control. The speed of this port is software selectable from 300 to 115,200 baud.
Includes:

• M1EZ8 Main Serial Interface
• 4 pieces of Double Sided Tape
• Plastic Housing
• CAT5E Patch Cable Assembly
• Instructions

The ELK-M1XEP is an Ethernet Appliance with a RS-232 Serial Port Interface. It may be used to connect a control in the M1 Family to an Ethernet network. It features email event notification and FIPS compliant encryption algorithms for security sensitive environments. It is powered by an ELK-P1216 12 Volts DC, 1.5 Amp plug-in power supply/adapter. A software setup utility is built into ElkRP for configuring the connection setup, network password, etc. The M1 Ethernet Interface is factory defaulted to obtain a dynamic IP address from a DHCP server (i.e. router, cable modem, etc.). It may optionally be setup with a static IP address.
Includes:

• M1 Ethernet Interface
• Plastic Housing
• 4 #6 Plastic Anchors
• 4 #6 Pan Head Sheet Metal Screws
• ELK-P1216 1.6A, 12Vdc Power Supply
• ELK-W040A DB9 Pin Serial Cable Assembly
• Instructions

Features:

• The HSM2204 is a dual-purpose module that provides programmable outputs for controlling external devices, and provides an additional +12 V 1.0 A of additional power
• Connect up to 4 modules per system
• Fully supervised for AC failure, low battery and AUX failure
• Compatible with HS2016, HS2032, HS2064 and HS2128 control panels

Compatible with the HS2016, HS2032, HS2064 and HS2128 control panels.

Features:

• Backlit numeric/symbol display
• Easy, universal-comprehension
• Actual Visual & Audible Transmitter
• Signal Strength Metering
• 3 Built-in Panic buttons, including programmable fire
• Concealed zone directory
• For use with Gemini GEM-P800 Hardwire/Wireless Controls