S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
The ELK-965 is a Low Battery Cutoff Module combined with a Master Power Switch. It is designed to work with virtually any 12 Volt control panel or power supply. In the event of an extended power outage, the ELK-965 sensing circuit automatically disconnects the battery when the voltage falls below 10 Volts DC. This helps to prevent "deep discharging" of the battery. The convenient power switch permits the installer or user to easily disconnect both the Battery and the AC power from the control or power supply.
Includes:
- 1 Low Battery Cutoff & Master Power Switch
- 2 pieces of Double Sided Tape
- Instructions
- Works With Any 12 Volt Control Panel
- Automatic Low Battery Cutoff Protects Battery From Deep Discharge
- AC and Battery On / Off Power Switch
- Visual LED Power Indicator
- Installer Friendly - Small Compact Size
- Includes AC Wires & Battery Leads
- Fits Standard Snap Track
- Includes Double Sided Mounting Tape
- Lifetime Limited Warranty
- Relay Contacts: Form "C", 7 Amp @ 28 VDC
- On / Off Power Switch: DPDT Slide Type
- AC Power Leads: 18 AWG, 18" Length
- Maximum Transformer Size: 18 VAC
- Battery Leads: 18 AWG, 18" Length
- Low Battery Cutoff Voltage: ~ 10 VDC
- Size: 1.75 in. X 2.185 in.(44.5mm X 55.5mm)
The ELK-924 Sensitive Relay module features DPDT (Form "C") dry contacts for general purpose switching of devices or high current loads. It operates on 12 or 24 volts DC and can be triggered with a negative or positive input at an incredible low current of only 1 milliamp.
Also available in a 4 pack (ELK-9244) which is packaged as 4 relay modules grouped on a pre-scored break-off circuit board.
Includes:
- (1) ELK-924 Relay
- 6 pieces of Double Sided Mounting Tape
- Instructions
- Super Low 1.2 mA Trigger Current
- Positive (+) Or Negative (-) Trigger Input
- Double Form C Contacts DPDT
- Heavy Duty Contact Rating
- On Board LED Status Indicator
- Includes Double Sided Mounting Tape
- Mounts in Standard 2.75 in. Snap Track
- Packaged in Reusable Poly Storage Box
- Lifetime Limited Warranty
- Operating Voltage: 12 or 24 Volts DC, jumper selectable
- Current Draw: 60mA (both relays on)
- Relay Contacts: Form C , 7A @ 30VDC, 10 A @ 125VAC
- Size: 1.5 in. X 2.75 in.
- Trigger Voltage: 5 - 24VDC
- Trigger Current: 1.2mA @12 VDC
The DSC ADP1310W-NAU is a power adapter that can be used with the 3G4000USA, LE4000E-AT, GS3060, and 3G3070 cellular radios. Most of these radios can be powered off of the alarm system itself, but if you're drawing quite a bit of power from the panel already then this adapter will provide the cellular radio with its own independent power source.
The adapter measures 4" (H) x 2.375" (W) x 2" (D) in size and provides 13.8 VDC / 1A of power for the DSC cellular communicators. It is rated to be used on 100-240VAC power systems that are rated at 50/60Hz.
- Add up to four high performance EchoStream wireless transmitters to any installation
- LED allows the user to view the current status of all four transmitters
- Five form C relays for connecting to any panel: four alarm, one fault
- Outputs can be configured in follower, latching, momentary, or toggle modes independently
- Case tamper protection, jam detection, and internal antennas for a secure wireless implementation
- Wireless programming routine built into the receiver
S2K Administration - Form Template Display
Actions